Strike Water Temperature Calculator
Hitting your mash temperature starts here. Enter your grain bill, grain temperature, target mash temp, and water-to-grist ratio — get the exact strike water temperature and volume.
Results
Formula used: –
How the strike water formula works
Grain absorbs heat — about a fifth as much per degree as the same weight of water (that's the 0.2 constant). The standard infusion equation balances the heat: Tw = (0.2 ÷ R) × (T2 − T1) + T2, where R is your water-to-grist ratio, T2 is your target mash temperature, and T1 is your grain temperature.
In practice, heat your strike water a couple of degrees hotter than calculated — your mash tun steals heat — then stir and check with a thermometer after doughing in. See what mash temperature does to your beer for choosing your target.
A worked example, start to finish
Say you are brewing an all-grain pale ale: 10 lb of grain stored at 70°F, a target mash temperature of 152°F, and a water-to-grist ratio of 1.25 qt/lb. The equation gives:
Tw = (0.2 ÷ 1.25) × (152 − 70) + 152 = 0.16 × 82 + 152 = 165.1°F
So you heat your strike water to about 165°F, or 167 to 169°F if your mash tun is cold and unpreheated. The volume is just grain weight times ratio: 10 lb × 1.25 qt/lb = 12.5 quarts, which is 3.125 gallons. Notice what drives the answer. The grain temperature gap (82 degrees here) is the big term; the ratio decides how much of that gap the water has to cover. Thinner mashes need less extra heat because there is more water sharing the load.
Strike temperatures at a glance
Same grain temperature (70°F) throughout. Find your target, read across to your ratio:
| Target mash | 1.0 qt/lb | 1.25 qt/lb | 1.5 qt/lb | 2.0 qt/lb |
|---|---|---|---|---|
| 148°F | 163.6°F | 160.5°F | 158.4°F | 155.8°F |
| 152°F | 168.4°F | 165.1°F | 162.9°F | 160.2°F |
| 156°F | 173.2°F | 169.8°F | 167.5°F | 164.6°F |
Two patterns worth remembering. Cold grain changes everything: the same 152°F target with grain stored in a 50°F garage needs strike water at about 168°F even at 1.25 qt/lb, because the gap grows from 82 to 102 degrees. And every row assumes the grain and water reach equilibrium; a cold metal tun pulls the real mash a few degrees lower, which is why preheating the tun matters more than decimal places.
Common strike water mistakes
- Guessing the grain temperature. Grain stored in a cold garage or a warm kitchen can be 20°F off the room thermostat. Stick the thermometer probe in the grain bin, not the air.
- Doughing in all at once. Dumping all the grain into the water creates dry clumps (dough balls) that insulate themselves and skew your reading. Add grain gradually, stirring as you go.
- Trusting the first reading. Temperature is uneven for the first few minutes. Stir thoroughly, wait two or three minutes, then measure in the center of the mash.
- Chasing one degree. A mash at 151°F instead of 152°F will not change your beer in any way you can taste. A mash at 162°F instead of 152°F will. Correct big misses; let small ones ride.
- Forgetting the fix math. If you land low, stir in small additions of boiling water and re-measure. If you land high, stir longer and add a splash of cool water. Small, measured corrections beat one big pour.
Frequently asked questions
How do you calculate strike water temperature?
Strike temp = (0.2 ÷ ratio) × (target mash temp − grain temp) + target mash temp, with ratio in qt/lb. The calculator above handles the math including metric units.
What is a good water-to-grist ratio?
1.0–2.0 qt/lb (about 2.1–4.2 L/kg) for most single-infusion mashes. 1.25 qt/lb is the classic starting point.
Should strike water be hotter to account for tun heat loss?
Yes — preheat your tun with hot water, or heat strike water 2–4°F above the calculated number and stir down to target after doughing in.